How to Fix Xbox One Controller Drift

0
188

When an Xbox One controller starts struggling with drift, you’ll typically notice undesirable movement while doing offers. It’s known as controller drift, or analog stick drift, because either thumb sticks will drift, or move, within an undesired direction even if you aren’t touching them.

To repair Xbox One controller drift, you have to go ahead and take controller apart and repair or replace a number of components associated with the analog sticks.

What’s Xbox One Controller Drift?

The most typical situation involves drift within the left analog stick, which often manifests inside your character constantly searching in first-person games. However, the best stick may also are afflicted by drift issues. You may even observe that whenever you move among the analog sticks in almost any direction, it’ll continue registering that movement despite taking your thumb from the stick.

When Xbox One controller drift occurs, you will find three primary causes:

Worn-out thumbstick pad: Each thumbstick includes a boxy sensor component having a moveable shaft on the top along with a rubber or plastic ingredient that snaps to the shaft. When the rubber or plastic piece becomes worn, replacing or repairing it’ll fix your drift issue. In some instances, an identical issue can result from dirty thumbstick pads.

Worn-out springs: Each thumbstick sensor component has two springs which help snap it to the middle if you remove your thumb. When either springs put on out, you’ll notice drift. Replacing the springs fixes this problem.

Bad thumbstick unit: Each thumbstick includes a boxy sensor component that’s soldered towards the controller circuit board. This component can fail internally, by which situation the only real possible fix is to replace it all with a brand new part.

How you can Fix Worn-out Thumbstick Pads

If you see that the Xbox One controller is struggling with thumbstick drift, you’ll want to begin with the simplest fixes and continue after that. While dirty or worn-out thumbstick pads don’t represent the most typical supply of this issue, this is actually the best starting point since it’s the fastest and easiest factor to test.

To do this fix, you’ll need:

  • Isopropyl alcohol
  • Cotton swabs
  • Prying tool
  • T-8 or T-9 safety Torx
  • Shim of the selecting or substitute thumbstick pads

Once you’ve collected individuals products, here’s how you can carry out the fix:

  1. Apply isopropyl alcohol to some cotton wool ball.
  2. Pry back the thumbstick, and thoroughly wipe the rounded surface with alcohol.
  3. Rotate the thumbstick incrementally, carefully washing the entire factor.
  4. Check to make certain that you’ve fully cleaned the thumbstick, and test operation.
  5. When the thumbstick still sticks or drifts, disassemble your Xbox One controller utilizing a pry oral appliance T-8 or T-9 safety Torx.
  6. Look into the thumbsticks to find out if they are positioned properly, and check out wiggling them to find out if they are loose.
  7. When the thumbstick pads feel loose, take them off.
  8. Switch the thumbstick pads with brand new ones, or reinstall having a shim just like a sliver of paper or plastic, and determine when they feel loose.
  9. Reassemble the controller and test operation.

How you can Fix Worn-out Xbox One Controller Thumbstick Springs

Should you still experience drift after trying to fix your thumbstick pads or determine that they are neither dirty nor loose, then your next easiest fix would be to replace your thumbstick springs. If perhaps one thumbstick is providing you with trouble, only switch the springs with that thumbstick.

To do this fix, you’ll need:

  • Prying tool
  • T-8 safety Torx
  • Analog stick springs
  • Tweezers

Lots of controllers, including Xbox 360 Console controllers, make use of the same analog stick component because the Xbox One controllers, so that you can take springs from your old controller. To keep your a substitute analog stick and go ahead and take springs from that.

Here’s how you can switch the springs within an Xbox One controller analog stick:

  1. Disassemble your controller utilizing a pry oral appliance T-8 or T-9 safety Torx.
  2. Carefully pry from the eco-friendly plastic covers at the base and right side from the thumbstick set up.
  3. Should you break either plastic cap, you’ll have to switch the entire analog stick module, which requires soldering.
  4. Take away the springs.
  5. Replace new springs, or springs obtained from another controller.
  6. Reassemble your controller and test operation.

How you can Replace an Xbox One Controller Analog Stick

In some instances, you’ll discover that either of the analog sticks are simply worn-out and have to be replaced. It is really an difficult repair, and also you shouldn’t attempt it should you aren’t confident with desoldering and soldering.

Don’t attempt this fix without having experience desoldering aspects of a circuit board. Any mistakes using the desoldering tool or soldering iron could easily ruin your controller.

If you wish to attempt this fix, you’ll need:

  • Prying tool
  • T-8 or T-9 safety Torx
  • T-7 Torx
  • Desoldering tool
  • Soldering tool
  • Solder
  • Substitute analog stick set up

Here’s how you can replace an Xbox One controller analog stick:

  1. Disassemble your controller utilizing a pry oral appliance T-8 or T-9 safety Torx to consider apart the situation along with a T-7 Torx to get rid of the circuit board.
  2. Make use of a desoldering tool to get rid of that old analog stick set up in the circuit board.
  3. Soldering an Xbox One controller analog thumbstick set up.
  4. Reassemble the controller and test operation.

If these pointers aren’t resolving the problem(s), it may be time for you to spring for any new controller. A minimum of you know you gave it your very best shot.

How do you fix sticky buttons with an Xbox One controller?

If you are experiencing sticky buttons with an Xbox One controller, unplug the controller and dip a cotton wool ball into rubbing alcohol. Lightly clean the region in which the button is sticky, carefully being able to access all of the the nooks and crannies you are able to achieve.

How do you fix an Xbox One controller that will not switch on?

To repair an Xbox controller that will not switch on, try installing new batteries. Look into the battery contacts, that ought to extend in an position. Make use of a prying tool if you want to bend one out. Also, look at your cables increase your Xbox One controller firmware.

How do you update an Xbox One controller?

To update an Xbox One controller’s firmware, switch it on and sign to the Xbox Network. Press the Xbox One button to spread out the guide and visit System > Settings > Kinect & devices > Devices & accessories. Select More (three dots) > Firmware version > Update now.

Was this site useful?

LEAVE A REPLY

Please enter your comment!
Please enter your name here